News
An industrial fan curve shows how a fan’s pressure capability changes as airflow changes under defined conditions. When the fan is connected to ductwork and equipment, its actual operating point depends on both the fan and the resistance of the complete system. Reviewing that relationship helps buyers compare models against a real project requirement instead of relying on a free-air airflow figure alone.
What does a fan curve show?
A typical performance chart plots airflow on the horizontal axis and pressure on the vertical axis. A curve applies to a specific fan size, speed, and configuration. Depending on the manufacturer, the chart may also show power, efficiency, or sound at selected points. Always check the chart notes for units, pressure definition, air density, and test conditions before comparing models.
Fan curve and system curve: how they work together
The fan curve describes the performance the fan can provide. The system curve represents the pressure needed to move air through the connected installation. Duct length, elbows, filters, dampers, hoods, and other equipment all add resistance. The point where the fan curve meets the system curve is the operating point, also called the duty point. It indicates the airflow and pressure the system is expected to deliver under those conditions.
If the system resistance is higher than estimated, the operating point can shift and airflow may fall. This is why a fan selected from airflow alone may not meet the requirement after installation.
How to read an industrial fan curve for selection
1. Define the required duty point
Start with the required airflow and the pressure needed at that airflow. Include the full air path and connected equipment, not just the fan. For a ducted installation, gather the route, dimensions, fittings, filters, and dampers so the system resistance can be assessed.
2. Confirm the pressure basis
Check whether the project specification and the performance chart use static pressure or total pressure. Compare like with like. If the pressure basis is unclear, ask the project engineer or supplier to confirm it before selecting a model.
3. Locate the operating point
Find the required airflow on the horizontal axis and the corresponding pressure on the vertical axis. Compare that duty point with the fan curve and the manufacturer’s recommended operating range. A suitable model should meet the project requirement under the stated conditions.
4. Review power and operating conditions
Once the duty point is identified, check the corresponding power requirement and the manufacturer’s operating limits. Also consider efficiency, noise, motor capacity, control method, and expected operating hours. These factors matter when comparing options for continuous or variable-load service.
5. Include the installation layout
Inlet and outlet arrangements can affect installed performance. Tight elbows, abrupt transitions, nearby obstructions, or uneven flow close to the fan may create system effects. Share drawings or photos of the planned layout when requesting a selection.
Why can installed airflow be lower than expected?
Common causes include underestimated duct losses, restrictive or dirty filters, partially closed dampers, extra fittings, or an inlet and outlet layout that creates turbulence. Air temperature, altitude, and the properties of the air or gas being moved can also affect performance. If the operating conditions differ from standard air, include those details in the selection request.
Information to prepare before requesting a fan selection
- Required airflow and pressure, including the pressure basis
- Duct route, length, elbows, filters, dampers, and connected equipment
- Air temperature and the medium being conveyed
- Dust, moisture, fumes, or other particles in the air stream
- Installation position, available space, and connection details
- Voltage, frequency, control method, and operating schedule
These details help a supplier assess whether a centrifugal fan or an axial fan is appropriate for the required duty point. POPULA FAN provides industrial fan options for different airflow and pressure requirements. For project-specific information, contact POPULA FAN with the system conditions.
Frequently asked questions
What is the operating point of an industrial fan?
It is the airflow and pressure point where the fan performance curve meets the system resistance curve.
Why is airflow alone not enough to select a fan?
The connected ductwork and equipment create resistance. The fan must deliver the required airflow while overcoming that pressure requirement.
Can ductwork change fan performance?
Yes. Duct length, bends, filters, dampers, and inlet or outlet arrangements affect system resistance and can affect installed airflow.
What should I send when requesting a fan recommendation?
Provide the airflow, pressure, duct layout, air temperature and medium, installation details, electrical requirements, and operating conditions.
Technical references: AMCA: Fan and System Curves · Greenheck: The Basics of Fan Performance.